"This is an awesome post, thanks. I have used up all of my mixes. Is there a way to do it with only one mix? That is all I have left.
"
Arnt-Inge Hansen's Discussions
Spektrum DX8, 6 flights mode with one singel channel, by FM and Gear Switch
Started this discussion. Last reply by Chad P Feb 9. 1 Reply 2 Likes
If you want 6 flights mode with Gear and Flightmode 1,2 switch with only using one channel (CH5) the following can be done with dx8 and maybe DX7:Go to servo set up, set Gear to 85% and 65% in…Continue
Hexacopter does not work in cold environments
Started this discussion. Last reply by Martint BuildYourOwnDrone.co.uk Oct 23, 2011. 10 Replies 0 Likes
HiI've built myself a hexacopter purchased from the martint (build your own drone) that has verygood service:) I have spektrum dx8 as r/c controllerI have a strange problem,…Continue
Does anyone know where the nearest ardupilot shop is in relation to Norway
Started this discussion. Last reply by Arnt-Inge Hansen Sep 22, 2011. 2 Replies 0 Likes
Does anyone have a list which countries ardupilot can be ordered from?Continue
Is there anyone who has made octocopter with the help of ardupilot.
Started this discussion. Last reply by Dani Saez Sep 23, 2011. 8 Replies 0 Likes
I will build me a octocopter with the help of ardupilot, has anyone a recipe for doing this. Looks to me droidworx as frame. Have just found that ardupilot used as Hexacopter, but as Octoctocopter.Continue
Arnt-Inge Hansen's Page
Latest Activity
Chad P replied to Arnt-Inge Hansen's discussion Spektrum DX8, 6 flights mode with one singel channel, by FM and Gear Switch
Arnt-Inge Hansen replied to Chris Anderson's discussion ArduCopter 2.3 released"Challange and entertainment
http://www.youtube.com/watch?feature=player_detailpage&v=YQIMGV5vtd4"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.2 beta"Do you use APM1 or 2, what type of frame?
I am waiting for my shipping of apm 2 maybe apm1 will do the job in the meantime?"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.2 beta"hi
Have tryed smaller props?"
Arnt-Inge Hansen replied to Tomas Soedergren's discussion Parasitic current in AttoPilot voltage/current sensor signal cable. Problem?? in the group ArduCopter User Group"I put a ferrite on the atto cable, the noise was more or less gone that way. This can be read in all baro if I remember right. I will not do…"
Arnt-Inge Hansen replied to Adam Rivera's discussion Shuttercable APM connection"There are several way to do that, 1: bye a shutterbugpro 2: use the internal relay on apm 3: bye a vitual servo switch. For my self I am using shutterbugpro on a canon 450 dslr, but I am sure there is code for activating apm relay for this in apm.
"
Arnt-Inge Hansen replied to Adam Rivera's discussion Camera Stabilization (Tilt) w/ infinite servos (360)"Have you a picture how to do?"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.1.1 alpha"yes separate bec for the sonar helps a lot, you can also try ferrite on wire from bec to sonar"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.1.1 alpha"If you use current/volt sensor it generate lots of noise. If you unplug the snsor from apm you can see the noise disappear"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.1.1 alpha"I am 100% agree with you. The observations I made with my new DJI Hexa agrees well with what you say. When I hover without gps the copteret is more stable than with GPS. With GPS the copter begins to drift like observed on a garmin gps. My…"
Arnt-Inge Hansen replied to Ruwan's discussion Works indoors, Beeps outdoors"I live in Norway, very cold outside. I have had the same problem, you can not measure it, it's something in side the esc. The battery ground and the signal grounds must be hard wired. If you use jdrone power connection board(jcb) and separate…"
Arnt-Inge Hansen replied to Ruwan's discussion LiPo Question"The best is telemetry, but you can also buy lipo alarm to install in copter, this will notify you with lights and alarm. Inside this forum somewhere there is a code for voltsensors that…"
Arnt-Inge Hansen replied to Ruwan's discussion Works indoors, Beeps outdoors"It sounds like you are missing ground between apm board and esc (signal)"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.1.1 alpha"I have had my first flight with DJI wk in the night, I must say I'm impressed. it was rock solid right out of the box. Setup program…"
Arnt-Inge Hansen replied to jasonshort's discussion Arducopter 2.1.1 alpha"My question is the use in the code. There must be ways this great component can stabilize the cyclic of the drone to avoid corrections with the stick. "
Profile Information
- About Me:
- I have do rc since 14 years old
- Tell us a bit about your UAV interest
- think UAV is very exciting.
- Hometown:
- Tromso
Arnt-Inge Hansen's Blog
Hexa flying
Posted on November 26, 2011 at 5:00pm 6 Comments 3 Likes
Thank you Jason and everyone else in the ardu team for the great job done in this project!!
I've finally got Hexa to work, the setup is as follows (v2.0.49):Jdrone frame Hexa, Jdrone engine 880, jdrone 30 amp esc, 10x3, 8 prop, 2x4s lipo main batteri(6000 to 10,000 ma), Spektrum DX8 with telemetri, 2xcastlec becs connected to two blocking diodes one of the becs have his own 2s lipo to keeping the voltage stable if the main battery is overloaded. I have worked extensively with…
ContinueComment Wall
- No comments yet!
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
South African DIY Drones…
19 members
-
ArduPilot (legacy) User …
95 members
-
DIYDrones - CNC Project
60 members
-
Moderators
57 members
-
ArduCopter (traditional …
115 members
© 2012 Created by Chris Anderson.
