Austin Duff
Austin Duff
  • Male
  • Montgomery Village, MD
  • United States
Share Twitter
  • Blog Posts
  • Discussions (17)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Austin Duff's Discussions

Transmit Data To Ardustation Via Jumpers?

Started Sep 20, 2009 0 Replies

My Xbee's are being shipped, but in the mean time, is there any way I can transmit the data from my ArduPilot to my ArduStation via Jumper cables for testing purposes?

Xbee's Refuse To Communicate

Started this discussion. Last reply by Austin Duff Sep 21, 2009. 13 Replies

I have my ArduPilot (running ArduPilot_EasyStar_V23) setup with an Xbee Series 2 on the Adafruit adapter board, with RX going to TX on the ArduPilot, 5v going to the special 5v Pin on the ArduPilot,…Continue

Error Uploading to ArduStation

Started this discussion. Last reply by Pat Dec 16, 2011. 46 Replies

Hello, I am relatively new to this ArduStation. I attempted to upload the Ardustation demo program using the ftdi cable, but i recieve the error:avrdude: stk500_getsync(): not in sync:…Continue

Tags: demo, ardustation, programming, Error

 

Austin Duff's Page

Latest Activity

Profile Icon
Pat replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Looks like the ATMega that came with my Ardupilot kit from 3DRobotics was bad. I had another ATMega 328 from a Duemilanove that I swapped in and the code loaded without a problem.
Dec 16, 2011
Profile Icon
Pat replied to Austin Duff's discussion 'Error Uploading to ArduStation'
I'm having the same issue not being able to upload code to the Ardustation. The error message is: Binary sketch size: 22752 bytes (of a 32256 byte maximum)avrdude: stk500_getsync(): not in sync: resp=0x00avrdude: stk500_disable(): protocol…
Dec 16, 2011
Profile Icon
Chris Anderson replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Good point, Martin. I've updated the manual to remind people of that.
Nov 19, 2011
Profile Icon
Martint BuildYourOwnDrone.co.uk replied to Austin Duff's discussion 'Error Uploading to ArduStation'
As an additional update to the postings here, one of my customers pointed out that the chip is the "UNO" on the Ardustation and need to be selected to have the code compile and load without error!   Regards   Martin.
Nov 19, 2011
Profile Icon
Martint BuildYourOwnDrone.co.uk replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Just adding a link to some additional information on the Ardustation   Colin has done some fantastic work with…
Nov 2, 2011
Profile Icon
Arnt-Inge Hansen replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Now every thing working ,yess :) I had forgot to glide the cli switch to flight mode. When I switch to flight mode the blue led light up.It is good to note that the engines must be armed in order…
Oct 31, 2011
Profile Icon
Heino R. Pull replied to Austin Duff's discussion 'Error Uploading to ArduStation'
If you have your aircraft's xbee up and running with Mavlink, The blue light should be illuminated on the Ardustation even before you select start feeds. If it isn't then there isn't communication between your Xbees. Also, on my…
Oct 31, 2011
Profile Icon
Arnt-Inge Hansen replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Hello  I was a little too quick to fresh sign ardustation, it looks like it does not communicate with apm. It is green in power led and the red light…
Oct 31, 2011
Profile Icon
Martint BuildYourOwnDrone.co.uk replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Hey Johann, Thanks for helping out buddy! Regards Martin
Oct 30, 2011
Profile Icon
Frank Vervoorst replied to Austin Duff's discussion 'Error Uploading to ArduStation'
I understand.   Thanks again. I will have fun.   Best, Frank
Oct 30, 2011
Profile Icon
Johann Van Niekerk replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Hi Frank   Glad you got it working now, they can be finicy , the only reason why i mentioned the cable was because if it was the board you would have recieved a different error msg.   Hope you have fun best Johann
Oct 30, 2011
Profile Icon
Frank Vervoorst replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Yippee, it works! Hi Johann, i've tested the cable without the board and became the same error message. Then I've testet with the board connected and  "Arduino UNO" Board selection and it works. I've done this some…
Oct 30, 2011
Profile Icon
Arnt-Inge Hansen replied to Austin Duff's discussion 'Error Uploading to ArduStation'
I forgot to say that it must be set on the potentiometer so that the text appears in the display
Oct 30, 2011
Profile Icon
Johann Van Niekerk replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Hi Arnt-Inge   Glad you got it ritte ;-) lets hope frank has the same luck   Best Johann
Oct 30, 2011
Profile Icon
Arnt-Inge Hansen replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Thanks a lot Johann, it work perfect now :)   I did the following : Selected Arduino Uno (top choice), uploaded http://code.google.com/p/ardustation-ii/downloads/detail?name=ArduStation2_APM_ACM_2.0.11.zip   From the…
Oct 30, 2011
Profile Icon
Johann Van Niekerk replied to Austin Duff's discussion 'Error Uploading to ArduStation'
Hi Frank / Arnt   Normaly when you get a Stk500 problem it means there is no communication to that board , to test this just plug in the ftdi cable and try upload with OUT the Ardustation being connected. if you get the same problem you…
Oct 30, 2011

Profile Information

About Me:
Kthx

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Top Content 

1 ArduCopter 2.3 released

ArduCopter 2.3 released
2 Incredible Flight Endurance!

Incredible Flight Endurance!
3 MinimOSD meets ArduCAM OSD Config

MinimOSD meets ArduCAM OSD Config
4 OpenCV aspirations

OpenCV aspirations
5 uav-skywalker parachute

uav-skywalker parachute

Groups

© 2012   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service

Sign in to chat!