Enzo Jia Male Toronto,On Canada: Like

0 members like this; Share Twitter

Blog Posts
Discussions (16)
Groups
Photos
Photo Albums
Videos

Enzo Jia's Apps (1)
Enzo Jia's Likes

Enzo Jia's Discussions

My Ardupilot 328 Mux didn't work

Started this discussion. Last reply by Jordi Muñoz Jun 11, 2009. 7 Replies 0 Likes

When i running the test code the ardupilot was very hot is it correct

Started this discussion. Last reply by Sgt Ric Jun 6, 2009. 12 Replies 0 Likes

When i finsh load ArduPilotNE to borad and the motor keeping runing is it corrrect

Started this discussion. Last reply by Enzo Jia Jun 4, 2009. 4 Replies 0 Likes

View All

Enzo Jia's Page

Latest Activity

estebanflyer left a comment for Enzo Jia

Hey Enzo, I was wondering if you were in Toronto these days, I'm trying really hard to make my quad fly with no success, everything works perfectly: GPS lock, xbee, radio modes, battery cells measurement, ESC calibration, compass, sonar....…

Aug 8, 2011

Jordi Muñoz replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

Also, in the code you must declare the PIN (D4) as input to leave it in high impedance and not pull down the attiny signal going to the multiplexor.

Jun 11, 2009

Jordi Muñoz replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

Try to force the MUX (D4) pin high with the atmega328 to see if the mux chip is damaged.. If yes send it back to SF

Jun 11, 2009

wayne garris replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

try to get more travel out of the channel you are using to control the mux.also Chris,it still says AT168 on the programming port.;)

Jun 10, 2009

Chris Anderson replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

I don't know. The MUX is designed for toggle switches (up, down and middle positions). It's really hard to support configuations that aren't the recommended ones and we've never seen before. Can you at least set it up the…

Jun 10, 2009

Enzo Jia replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

Now i unplug the CRTL wire the Mux light but GPS LED didn't blinking(photo) Why was this happen

Jun 10, 2009

Enzo Jia replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

because i use 4ch Remote control don't have Channel 5 and My Gps blinking but GPS LOCK was not working

Jun 10, 2009

Chris Anderson replied to Enzo Jia's discussion 'My Ardupilot 328 Mux didn't work'

In the pictures you don't have the CTRL input going to your Rx Channel 5, as instructed. Why not?

Jun 10, 2009

My Ardupilot 328 Mux didn't work

I bought a new Ardupilot 328 boards and connect showing on the photo and I run 1.0 code and test code,But no matter how i switch chanel to control CTRL the mux dosen't work ? I don't know why??

Discussion posted by Enzo Jia Jun 10, 2009

7 Comments 0 Likes

Sgt Ric replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

I see the site even mentions the possibility of the boards being from the first batch and the possible need to reflash them!

Jun 6, 2009

Enzo Jia replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

Thank you Chris I wil think about it .

Jun 6, 2009

Chris Anderson replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

We don't sell through them--I don't know where they got it (we only sell through Sparkfun) and I have no idea how old that board is. If it dates back from our first production run, back in January, it may have a firmware problem with the…

Jun 6, 2009

Enzo Jia replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

I bought it in robotcraft.ca .So what I can do now ?do i need to bought a new one?

Jun 6, 2009

Chris Anderson replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

The board is green. The green board hasn't been sold for three months (it's the old 168 board). Where did you buy it?

Jun 6, 2009

Enzo Jia replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

The Mux LED did not turn on and off when I toggle that channel And i just bought this board last week

Jun 5, 2009

Chris Anderson replied to Enzo Jia's discussion 'When i running the test code the ardupilot was very hot is it correct'

Does the MUX LED turn on and off when you toggle that channel? Also, I see you have one of the old boards. How old is it?

Jun 5, 2009

Comment Wall (1 comment)

At 10:14am on August 8, 2011, estebanflyer said…: Hey Enzo, I was wondering if you were in Toronto these days, I'm trying really hard to make my quad fly with no success, everything works perfectly: GPS lock, xbee, radio modes, battery cells measurement, ESC calibration, compass, sonar.... I'm stuck at PID's, the copter takes off in a very sluggish way, no matter how I tweak the PID's I always end in a crash, so I thought I might as well pay someone for their time and save money on propellers. (Also save time in balancing them)

Please let me know if you are available. I am at Dufferin and Bloor, but if you want I can take all my gear to you. My phone number is 905 616 8482 (not long distance; Mississauga). As I said, I'm willing to pay for your time. All I want is to have the quad flying.

Please help me out!

Esteban Díaz