"Can I sent it back to DIYdrones customer support for RMA issue? I have following all instruction from the manual and can not solve the loading firmware problem."
Gus5610's Discussions
ArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03
Started this discussion. Last reply by Chris Anderson Apr 3, 2010. 5 Replies 0 Likes
Gus5610's Page
Latest Activity
Gus5610 replied to Franck's discussion ArduMega"Dear Chris:
Many thanks for your help. I am sure I have been successfully downloading AMP software many times and also tested CLI without any problems. On receiving this new board, I was trying to upload the firmware loading via…"
Gus5610 replied to Franck's discussion ArduMega"@Chris
I just purchased full ArduPilot Mega kit this month, done all solider work, upload the APM 2.1 and all well success but yesterday when I uploaded new updates AM 2.11 into AMP board it takes long time and can not upload in…"
ModeratorChris Anderson replied to Gus5610's discussion ArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03
"Same advice. Try Radio Mode 1 if you're having trouble with Radio Mode 0."
Cronselaar replied to Gus5610's discussion ArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03"Hi
I have the very same setup as you have. Also have the same problems as you. I do however get the right readings from the servo's. Switching between Stabilize and RTL also made the ardupilot freeze. It even went into a mode(which I could not…"
Gus5610 replied to Gus5610's discussion ArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03"Chris & Saifu
Thanks for help. I will try it this weekend and report it."
Saiful Azuwan replied to Gus5610's discussion ArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03"Gus5610,
I'm using the same setup as you. But with the 2.5.04 code. The stabilizer mode rock!!
Today I give a test Auto & Fly By Wire mode. All work but my ez* keep descending. In RTL it loiter & also descending.
But overall the code…"
ModeratorChris Anderson replied to Gus5610's discussion ArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03
"Use the latest code (2.5.04 or 2.6) and try Radio Type 1
//3-2
#define RADIO_TYPE 1 // 0 = sequential PWM pulses(Fasst, Spektrums), 1 = simultaneous PWM pulses (Corona RP8D1)"
Gus5610 posted a discussionArduPilot 2.46 work out brillient but never ok wz 2.5.02 or 03
I used to fly Ardupilot with 2.46 and it works without any problems and very happy about its performance but recently I have been upgrading from 2.46 into 2.502 or 2.503 but never work it out. It seems that CH1 and CH2 serve plus can not be detected. I use Ardupilot_25_Radio_test test it and finf out all CH1 and CH2 plus all under 1000. I move to CH1 rudder left @857, Center @850, Right @853 but while I move CH1 to left @857, my CH2 also move from 959 to 1028.....that is a very strange movement…See More
Gus5610 commented on jasonshort's blog post AP with Ground Station and 2-way comm"I tried the above 1-7 steps you mentioned to run the adobe flash player of Ground Station but encounter a problem from serproxy: Fail to open Comm port - Connection refused. How do I solve this problem?
Cheers"
Gus5610 commented on Chris Anderson's blog post ArduPilot main page"Fefenin: I might help you. When u are in Taiwan. U can buy Easy Star from Taiwan eBay @NTD1500 and u can choose to pay money to the delivery staff when u receive it wz about NTD150-200 extra see the…"
Gus5610 commented on Bryan Cuervo's blog post Flight tests with ArduPilot in EasyGlider Pro"Hi, I am new here and hope if any one can help me out with the Fly_By_Wire in manual mode.
My Fly-by-wire is not working as well in manual mode but i works in WP and RTL mode. I have change FLY_BY_WIRE_GAIN_ROLL & Pitch @16 or 8 or even 40,…"
Comment Wall
- No comments yet!
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
ArduCopter (traditional …
115 members
-
DIYDrones - CNC Project
60 members
-
ArduPilot (legacy) User …
95 members
-
South African DIY Drones…
19 members
-
Moderators
57 members
© 2012 Created by Chris Anderson.
