Mattia Parise
  • Male
Share Twitter
  • Blog Posts
  • Discussions (9)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Mattia Parise's Discussions

Big crash

Started Mar 20 0 Replies

Hi to all. Yesterday my Y6 drone crashed...But there are 2 problems about that:1) after changing the CH6 switch to change pitch of camera gimbal I lost control of the copter ( I thing apm rebooted,…Continue

Problem With Camera Gimbal

Started this discussion. Last reply by Mattia Parise Feb 17. 2 Replies

Hi to all. I have a Droidworx camera Gimbal. It is working well for roll, but for tilt i noticed that i have a problem of 90 degrees. The middle position of the gimbal is not at middle position (0…Continue

Problem With Waypoints (Especially Setting Home waypoint)

Started Jan 6 0 Replies

Hi to all, I like a lot this site. I'm trying to develop a Y6 arducopter. No problems for the assembly, zigbee telemetry works fine,(a little problem is that when I use that I can't read any…Continue

 

Mattia Parise's Page

Latest Activity

Mattia Parise posted a discussion

Big crash

Hi to all. Yesterday my Y6 drone crashed...But there are 2 problems about that:1) after changing the CH6 switch to change pitch of camera gimbal I lost control of the copter ( I thing apm rebooted, why did this happened?) 2) I have a log where roll and pitch are always about 600-1000 but yaw is everytime about 20000... Is this normal?I've attached the log.Thanks to everyone for your support.MattiaSee More
Mar 20
0 Comments
Mattia Parise replied to Jean-Luc Combe's discussion XBee and APM 1.4 communication problem
"Hi Don. I've just done it 3 times. Nothing changes. The MultiSerialMega code works. But if I invert the two xbees, it does not work. The problem is that one xbee cannot transmit or one cannot receive. I think this is the problem..."
Mar 19
Mattia Parise replied to Adam Rivera's discussion XBee 900Mhz Telemetry Stopped Working
"Hi Jan. It is avoiding it of course, but I can't connect to the terminal (i see only rubbish words in terminal through xbee). Another thing: if I upload the test code it is working in one way, but if I change the Xbees it does not work. I am…"
Mar 14
Mattia Parise replied to Jean-Luc Combe's discussion XBee and APM 1.4 communication problem
"Sorry for the double Post, but I have to add some information: I am using the 900mhz kit. Also I noticed that inverting the xbee only one adapter has the RSSI led on. So one XBEE does not receive any data, but can only send. This is a big problem...…"
Mar 14
Mattia Parise replied to Adam Rivera's discussion XBee 900Mhz Telemetry Stopped Working
"Adam, did you get it working? I have the same issue. I unbricked them, but the problem is that the test with the print("Serial 3") works, but APM does not work. I think the problem is that the copter's xbee does not receive anything.…"
Mar 14
Mattia Parise replied to Jean-Luc Combe's discussion XBee and APM 1.4 communication problem
"Hi to all. I know this is a quite old post but it is the same problem I have. Xbee has been working till yesterday. But the MultiTest works, I can read Serial3 on the SerialPort Monitor. But when I connect through APM Planner it stops at getting…"
Mar 14
Mattia Parise replied to Mattia Parise's discussion Problem With Camera Gimbal
"Hi Duran. Thanks for your answer. I made that. But my Gimball only works for 90 degrees and not for 180. Do you know how can be this?"
Feb 17
Duran DeV replied to Mattia Parise's discussion Problem With Camera Gimbal
"Hey, I have the same gimbal, you can adjust where the tilt is pointing by simply moving the pot on the tilt with your hand, it might be a bit hard to move but it does, just move the pot until you have your tilt where you want it. simple. no need to…"
Feb 17
Mattia Parise posted a discussion

Problem With Camera Gimbal

Hi to all. I have a Droidworx camera Gimbal. It is working well for roll, but for tilt i noticed that i have a problem of 90 degrees. The middle position of the gimbal is not at middle position (0 degrees), but is 45 degrees down. So the lowest position is not 90 degrees down but middle position, and the highest is 90 degrees down( I am talking about RC input down =0, medium =1, high = 2).So the camera won't look up because I am wrong of 90 degrees, but only down... How can I solve this…See More
Feb 16
2 Comments

Profile Information

About Me:
...
Tell us a bit about your UAV interest
...

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.

A list of all T3 contests is here. 

 

Top Content 

1 What do you think the APM should do on fail safe

What do you think the APM should do on fail safe
2 ArduCopter 2.5 released!

ArduCopter 2.5 released!
3 Housekeeping note: Kevin Finisterre

Housekeeping note: Kevin Finisterre
4 Hexa-copter found after failed attempt of delivering cell phones to inmates of a Brazilian penitentiary

Hexa-copter found after failed attempt of delivering cell phones to inmates of a Brazilian penitentiary
5 Control Software

Control Software

Groups

© 2012   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service