"After loading 2.3.3 I did some ground testing but did not give any reliable results so I set the code for walk around mode, still can be sure its working. Now after setting the .h file back to normal mode the serial monitor prints out as it used to…"
Mikil P's Discussions
Waypoint
Started this discussion. Last reply by Paul Har Aug 4, 2009. 5 Replies 0 Likes
Mikil P's Page
Latest Activity
Mikil P replied to Mikil P's discussion Waypoint"hi bryan,
I finally managed to do some testing yesterday with the weather being good. I flew in RTL mode.........and it seem to go somewhere towards the sunset.....:(
Also another problem I have, is that it always goes to the home position first…"
Mikil P commented on Jordi Muñoz's blog post ArduPilot Shield Assembly Instructions"hi, i have also got a new Locosys. I was using it to build a groundstation for a university project. I see the Locosys is set up at 57600 baud rate. I was wondering why when we choose NMEA mode in ardupilot vesion 2.2.3, it changes it to a baud rate…"
Bryan Cuervo replied to Mikil P's discussion Waypoint"From what I've read the measured altitude is always AGL (above ground level). I'll have to check the utility next time I fly and see what the max alt. and airspeed says. I'm using a pitot-static tube, not the type that Chris and Jordi…"
Mikil P replied to Mikil P's discussion Waypoint"Bryan,
I flicked the switch for the RTL mode, it did seem to want to come home however the wind on the day was dreadful, so i'm going to do some further testing next week (hopefully the weather holds out) and will let you know the results I…"
Bryan Cuervo replied to Mikil P's discussion Waypoint"Mikil,
I've been test flying versions of Ardupilot for quite a while now and one day the plane flies as expected and the next, she'll do something completely different (without any code changes). The only variable I can think of is the…"
Mikil P posted a discussionWaypoint
Hi there,I tested my Easystar yesterday at the local park, i was using the ardupilot 2.23 (latest) code, with the shield. I added the waypoints using the desktop utility and all seem to work well. The easystar went to the waypoints set. However i decided to go the the RC flying club the following day, again using the same setup, the only difference was that I put in the waypoints that match the flying club. This time round the easystar started flying towards a point that was not added using the…See More
Mikil P commented on Stephen Jack's blog post Throttle Control"I've got it working now.....thanks for your help."
Mikil P commented on Stephen Jack's blog post Throttle Control"Hi Chris, Yes I am using the shield with airspeed sensor and the Pitot tube is plugged into the top nipple. The altitude for each waypoint is about 50m."
Mikil P commented on Stephen Jack's blog post Throttle Control"I went test flying yesterday, as soon as I switched onto the waypoint mode (middle switch), my throttle cut off. Does anyone know where the problem lies? I am using ardupilot version 2.2.3 for the easystar."
Mikil P replied to Peter Seddon's discussion Ardupilot Config Tool Beta 3"Hiya -
Is the source available anywhere? The program doesn't run under Mono which means anyone who doesn't use Windows can't use the latest ardupilot. I'm quite happy to re-write the program in something a bit more platform…"
Mikil P posted a blog postAvailability of source code of ArduConfig Beta.
Hi,I am currently using a Linux based system and was wondering if the source code for the Ardupilotconfig tool (beta3 version) was available as I can't upload the waypoints on the board at the moment. I'm extremely interested in writing a platform neutral clone of ardupilotconfig, and would be quite happy to share the results. Is there any other way/method of uploading the waypoints manually assuming I am using the latest ardupilot code (Version 2.2.3) for the easystar ? Any help with this will…See More
Profile Information
- Hometown:
- London
Mikil P's Blog
Availability of source code of ArduConfig Beta.
Posted on July 2, 2009 at 4:57am 0 Comments 0 Likes
Hi,
I am currently using a Linux based system and was wondering if the source code for the Ardupilotconfig tool (beta3 version) was available as I can't upload the waypoints on the board at the moment. I'm extremely interested in writing a platform neutral clone of ardupilotconfig, and would be quite happy to share the results. Is there any other way/method of uploading the waypoints manually assuming I am using the latest ardupilot code (Version 2.2.3) for the easystar ? Any help… Continue
I am currently using a Linux based system and was wondering if the source code for the Ardupilotconfig tool (beta3 version) was available as I can't upload the waypoints on the board at the moment. I'm extremely interested in writing a platform neutral clone of ardupilotconfig, and would be quite happy to share the results. Is there any other way/method of uploading the waypoints manually assuming I am using the latest ardupilot code (Version 2.2.3) for the easystar ? Any help… Continue
Comment Wall
- No comments yet!
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
DIYDrones - CNC Project
61 members
-
ArduCopter User Group
617 members
-
UK Ardupilot Group
30 members
-
Telemetry over cellular …
68 members
-
ArduCopter (traditional …
116 members
© 2012 Created by Chris Anderson.
