"thanx for your help."
Raytrace Nomad's Discussions
Never ending story Xbee's
Started this discussion. Last reply by Ersin Acar Jan 26, 2011. 1 Reply 0 Likes
Configuration ok but no flight ?
Started this discussion. Last reply by Greg Fletcher Dec 28, 2010. 10 Replies 0 Likes
Raytrace Nomad's Page
Latest Activity
Raytrace Nomad commented on James masterman's blog post Mapping with Ardupilot"Could anyone link to spreedsheet for aerial coverage ?"
Raytrace Nomad replied to John L.'s discussion Sonar PID setup"Is sonar work with BPM together ? Or just choose one ?"
Raytrace Nomad replied to Bill Sanford's discussion PID tuning help??"First start with acrobatic mode , and first try I and D value 0. You can test on your hand after find unoscillated settings you could fly. P is rate for the gyro values between motor corrections. If give 0 you have no gyro correction.…"
Ersin Acar replied to Raytrace Nomad's discussion Never ending story Xbee's"Hi,
I'm using two of that http://www.sparkfun.com/products/9087 and never touch settings it's max rate is 9600 and its good for me :) if u want i can send my profile file at night."
Raytrace Nomad posted a discussionNever ending story Xbee's
Never ending story... Xbee's Could anyone share their xbpro 900 ' [ mine one with cable one with antenna which Arducopter Wiki offered ] x-CTU configurations [ if you could save them to file with Profile>save it's better] See More
Raytrace Nomad replied to F11music.com's discussion Wireless telemetry set up but not communicating with Configurator"Test code succesfull - i read port3 from computer but configurator still not connected...
"
Raytrace Nomad posted a discussionMy other boards have GyroYaw problem..
After connecting Configurator 1.22 everything looks ok but GyroYaw did not move , therefor APM did not make yaw correction. Is it hardware problem ? if not where i did a mistake ? I have one QUAD with same config [ same oilpan and APM buy new Magneto [ corrected resistor ]] it works great. Thanx for all toughts.See More
Profile Information
- About Me:
- RCMODEL,FPV
- Tell us a bit about your UAV interest
- Beginner Level
- Hometown:
- izmir
Raytrace Nomad's Blog
Trex Boom Copter Drawings ready and waiting for machining...
Posted on September 20, 2010 at 7:23am 11 Comments 0 Likes
Comment Wall (2 comments)
- At 3:16am on March 4, 2010,
Anthony Leroux said… - Ya anthonyler@mweb.co.za sounds good ,i am looking to put something together with camers to try and catch pouches in one of the gameparks in South Africa ,if i may i am new at this blog thing rest on you for info on the electronics of auto pilot stuff . I have been flyingRC planes a few years and have build and flown them .i am busy with a kantana 100cc at the moment but the uav is the next in line .Thanx Anthony
Delete Comment
- At 2:52pm on September 20, 2010, Ravi Gaddipati said…
- Hey,
If you would like, I can laser cut 1/16" garolite for you, for your frame. Great for center plates/ motor mounts (not boom clamps).
I can read CAD files (autodesk inventor 2011).
It will only cost you materials :)
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
DIYDrones - CNC Project
61 members
-
ArduCopter User Group
617 members
-
UK Ardupilot Group
30 members
-
Telemetry over cellular …
68 members
-
ArduCopter (traditional …
116 members
© 2012 Created by Chris Anderson.
