"I upload my video and it sound the motors seem try to stand the Quadcopter, but I don't know finnaly it's landing, can I adjust the PI control on altitude hold in APM Planner to get good configuration? now I currently use APM Planner…"
Sugeng Priyono's Discussions
motor DC brushless doesn't start
Started Dec 13, 2011 0 Replies 0 Likes
hi, I'm beginners of making Arducopter using APM 2560, I've followed all the instruction for uploading the software via APM mission planner 1.1.2, I've calibrated the ESC, and also the RC, but when…Continue
Sugeng Priyono's Page
Latest Activity
Sugeng Priyono replied to Sugeng Priyono's discussion Altitude Hold using sonar sensor in the group ArduCopter User Group
Cliff Dearden replied to Sugeng Priyono's discussion Altitude Hold using sonar sensor in the group ArduCopter User Group"Randy, is it possible to buy this improved barometer to replace the old one on the 1280 board? Knowing my
luck I bet the pin connections are differant and/or the software has to be modified. "
Sugeng Priyono replied to Sugeng Priyono's discussion Altitude Hold using sonar sensor in the group ArduCopter User Group"ok, thank you Mr. Randy...... I'm currently use APM 1.4
I still have a question.......why does not my Quadcopter fly stable?, it flies up and down when I switched to Alt_hold mode from My radio at 2 meters height. "
DeveloperRandy replied to Sugeng Priyono's discussion Altitude Hold using sonar sensor in the group ArduCopter User Group
"Both are used. Sonar for low altitude, Barometer for high altitude.
If you move to APM2, you'll find it has a much improved barometer..so much better than you may decide that you don't need a sonar."
Sugeng Priyono added a discussion to the group ArduCopter User Group
Altitude Hold using sonar sensor
now I currently use sonar that I used for the Altitude hold, can it work....????because when I saw the feature of APM sensor used for altitude hold is BarometerSee More
Sugeng Priyono replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group"so, where should I set the sensitivity to get the real control.....?????
when I calibrate the ESC with my radio, it sounds the throttle gives real signal to the ESC, it's known motors showing the real speed rotation, but when I put the…"
Sugeng Priyono replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group"Oh, I'm sorry, I was wrong when I typed it, I mean this my Rx"
Nick Mann replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group"First things first. That is your Rx. Your Tx is the big, programmable monster with sticks and a necklace. You can control what your sticks do from there. Take it slow."
ModeratorGareth Rens replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group
ModeratorGareth Rens replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group
"With your radio set to a normal throttle response. If you put 50% throttle, you get 50% output on the motors.
If you lower the sensitivity to 50%, then you give 50% throttle on the radio, it only gives 25% on the motors.
So your full travel is 100%…"
Sugeng Priyono replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group"what does per the wiki mean???
and where I can find the mixer on my Tx
Here is my Tx I use
"
Sugeng Priyono replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group"what does the double throttle when it's calibrated in APM mean...???? I've not understood yet"
ModeratorGareth Rens replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group
"also if you reduced your throttle response on your radio e.g half sensitivity. This would double the throttle when you calibrate in apm planner."
DaveyWaveyBunsenBurner replied to Sugeng Priyono's discussion throttle only has top speed in the middle of throttle stick.....Why????? in the group ArduCopter User Group"That sounds like a mixer on your tx is misconfigured.
1. Recallibrate ESCs as per the wiki
2. Check there are no mixers configured in your TX"
Sugeng Priyono added a discussion to the group ArduCopter User Groupthrottle only has top speed in the middle of throttle stick.....Why?????
what should I do if the the throttle stick has top speed in the middle position, and if I adjust to top position, the speed is reduced..... is there any solution???See More
Sugeng Priyono replied to Sugeng Priyono's discussion Problem with motor in the group ArduCopter User Group"no. after I've calibrated the RC, I have to center the throttle stick.....ok ok, thanks Mr. Dave for the information... I'll try the RC calibration again...."
Profile Information
- About Me:
- I'm a student of Mechatronic of EEPIS-ITS, and I wanna join in order to get many experiences about UAV specially quadrotor one
- Tell us a bit about your UAV interest
- UAV is nice beautiful looking vehicle when flying on the air.
- Hometown:
- Jombang, east java, indonesia
Comment Wall
- No comments yet!
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
DIYDrones - CNC Project
60 members
-
ArduCopter User Group
617 members
-
UK Ardupilot Group
30 members
-
Telemetry over cellular …
68 members
-
ArduCopter (traditional …
116 members
© 2012 Created by Chris Anderson.
