"Hello,
i found the soltion by using the direct Inputs of ATMEGA 1280 on red Board.
IN1...IN8 are only Inputs of 74LS154 Digital Multiplexer."
druckgott's Discussions
Ardupilot Mega V1.4 (Red Board) RC-Inputs use as Potentiometer Inputs
Started this discussion. Last reply by druckgott yesterday. 1 Reply 0 Likes
Hello,i want connect at least 4 Potis at Ardupilot Breadboard (i have only the red Board) and send its values via USB to PC.USB-Transmit works in steps of 1,5 sec but i think there has to be a…Continue
Tags: Potentiometer
Bug with 1.1.73 and Loiter Speed - Loiter P maybe inverted?
Started this discussion. Last reply by Michael Oborne Apr 22. 1 Reply 0 Likes
Hallo,I use 1.1.73 and AC 2.5.4If I check Tune CH6_Loiter_P the Loiter P don´t change, it Changes the Loiter speed.In what unit is Loiter speed? m/s?And is Loiter P with 2.0 default normal before it…Continue
Loiter and Loiter Rate Tuning???
Started Apr 5 0 Replies 0 Likes
Hallo, in MP there are two Loiter rates availible.CH6_Loiter_KP and CH6_Loiter_RATE_KP same for KI?What´s the differenc?thxdruckgottContinue
Bug on CH7 MP Option für min max
Started this discussion. Last reply by Michael Oborne Apr 6. 1 Reply 0 Likes
Hallo,today I have used the MP and tune Travelspeed.I set value min to 0 and max to 6.0Then I change the value via ch7 and read the params again.if i´m on 0 it´s 0 if I put it put to 100% it´s not 6…Continue
druckgott's Page
Latest Activity
druckgott replied to druckgott's discussion Ardupilot Mega V1.4 (Red Board) RC-Inputs use as Potentiometer Inputsdruckgott posted a discussionArdupilot Mega V1.4 (Red Board) RC-Inputs use as Potentiometer Inputs
Hello,i want connect at least 4 Potis at Ardupilot Breadboard (i have only the red Board) and send its values via USB to PC.USB-Transmit works in steps of 1,5 sec but i think there has to be a special command to define IN1 ... IN8 as ADC-Input.Can anybody help me?Thanks in advance/* ReadAnalogVoltage Reads an analog input on pin 0, converts it to voltage, and prints the result to the serial monitor. Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and…See More
druckgott commented on Andrew Radford's blog post Bluetooth Serial Communications with the APM"Switch of Firewall and Virus System I have the same problem with Putty"
DeveloperMichael Oborne replied to druckgott's discussion Bug with 1.1.73 and Loiter Speed - Loiter P maybe inverted?
"are you sure you have selected the right option? what about
CH6_LOITER_RATE_P"
DeveloperMichael Oborne replied to druckgott's discussion Button to clear Eprom
"there used to be one, but wasnt realy required."
druckgott posted a discussionBug with 1.1.73
Hallo,I use 1.1.73 and AC 2.5.4If I check Tune CH6_Loiter_P the Loiter P don´t change, it Changes the Loiter speed.In what unit is Loiter speed? m/s?And is Loiter P with 2.0 default normal before it was 0.5... or so and now Loiter P is 2.0 and Loiter speed is 0.5... or so, Could be there anything wrong?thxdruckgottSee More
druckgott replied to druckgott's discussion Button to clear Eprom"ok this works perfekt, but I think a button would also be quite nice if it´s posible?!"
druckgott replied to John Hanson's discussion 2.54 Rocks!"Oh I should also test this, looks realy good"
druckgott replied to Brady D's discussion Connection Error in APM Mission Planner with wireless telem"which data transfer rates do you meen?? Can you make a screenshot???"
druckgott replied to Brady D's discussion Connection Error in APM Mission Planner with wireless telem"I have exactly the same problem with a bluetooth module, I get the led lighning, but can´t get data back.
and after 30 seconds it crashed.
Over USB it works perfekt.
"
DeveloperMichael Oborne replied to druckgott's discussion Bug on CH7 MP Option für min max
"this looks like scaling issue, i will look into it"
DeveloperMichael Oborne replied to druckgott's discussion Button to clear Eprom
"the easiest way would be to use the planner to change "sysid_sw_mrev" to any other number, as on reboot it will reset to defaults."
druckgott replied to Randy's discussion ArduCopter 2.5 released!"Hi, I compare it also to 2.0.49 because this was the best one bevor for me.!!!"
druckgott replied to Ruwan's discussion Share your drone info thread"<p>My Copter:</p><p> </p><p>Motor to Motor <strong>560mm</strong>(edge to edge 720mm, that the motors are do not destryed on a crash)</p><p>Flightmode…"
Profile Information
- About Me:
- pilote
- Tell us a bit about your UAV interest
- multiwii and arducopter
Druckgott's Blog
How to burn a bootloader for APM2560 or APM1280 with a Pololu USB AVR Programmer
Posted on September 20, 2011 at 11:00am 1 Comment 2 Likes
I have a Atmega1280 Board with the IMU. On uploading the firmware 2.0.41 from Arducopter I get an error in MP.
After this MP can´t get my AMP version. So I decided to test it with arduino 22 and I get this error:
avrdude: stk500_getsync(): not in sync: resp=0x00
I testet many times and read many threads.
After testing…
ContinueComment Wall
- No comments yet!
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
ArduPilot (legacy) User …
95 members
-
Moderators
57 members
-
DIYDrones - CNC Project
60 members
-
ArduCopter Evolution Team
108 members
-
ArduCopter User Group
617 members
© 2012 Created by Chris Anderson.
