igal
  • Male
  • Israel
Share Twitter
  • Blog Posts
  • Discussions (12)
  • Groups
  • Photos
  • Photo Albums
  • Videos

igal's Discussions

Trying to setup UAV DEV BOARD and getting error when compiling.

Started this discussion. Last reply by igal May 7, 2010. 27 Replies

I have connected the ICD2 and everithing works.But when i try co BUILD the project i get this message:Skipping link step.  The project contains no linker script.BUILD FAILED: Fri Apr 23 16:48:41…Continue

 

igal's Page

Latest Activity

igal commented on Chris Anderson's blog post Announcing T-3, Round 3: The Reliability Round
"The go pro can take a snapshot every 2 sec . The gopro2 can take 2 snapshot each second"
Apr 5
igal commented on Chris Anderson's blog post Announcing T3-2, Round Two: the autotakeoff and landing round
"Hand lanching is for the weak arduinos . Real man taking off from ground .  "
Feb 9
igal commented on Chris Anderson's blog post Restarting the T3 Contest: Now with copters!
"Jeremy what is the wind direction ?"
Nov 28, 2011
igal commented on Pete Hollands's blog post DIY Drones T3 racing in Venice
"WOW this is great."
Nov 18, 2011
igal replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"First flight today!! Created simple 250mX100m 30m const struct relative3D waypoints[] = { { 0 , 0 , 30} , { -150 , 0 , 30} , { -150 , 100 , 30 } , { 100 , 100 , 30 } , { 100 , 0 , 30 } , } ; I took off in manual mode gain height and switched to…"
May 7, 2010
jonny replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Hi Igal Excellent news, good luck with the rest of the process"
May 3, 2010

DeveloperPete Hollands replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Igal, Super News."
May 3, 2010
igal replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"More good news This morning uploaded the HEX of 2.0.3 went outside after 15 seconds got GPS lock. I have assigned the flaps (3 positions) switch and tryed switching from MANUAL/STABILIZED/WAYPOINTS the leds gave the correct response. This evening…"
May 3, 2010

DeveloperWilliam Premerlani replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Hi Igal, Well, you have made some good progress, and all on your own, too. It has been so long since I ran the self-test software, I was not sure what it did, so I just loaded it up and ran it. Just to confirm. When you run the self test…"
May 2, 2010
Morli replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Congrats Igal, So to summarize your build failed issue/error, the issue was resolved by reinstalling MPlab in default location, Yes? The alternate method is to change the path in some file(?) in matrix pilot.this was successfully done by some one…"
May 2, 2010
igal replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Yeppppppiiiiiiii Got a GPS lock with the self test software. After about 10 seconds RED led on the GPS reciever started to blink !!!!! Tommorow (now realy it will be tomorow) i will try the Matirx Pilot ."
May 2, 2010
igal replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Today i have decided to start all over again. Installed the MPLAD 8.5 on its default location Installed the compilers on its default location Extracted the project again and everithing copiled first try(that is a good sign) With my old 7.3 D:…"
May 2, 2010

DeveloperWilliam Premerlani replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Igal, I agree with Peter, it would be a good idea to see if the UDB is receiving messages from the GPS. The is a possibility that there is an open solder joint between the GPS connector and the board. The way Peter has suggested is a good way to…"
May 2, 2010

DeveloperPete Hollands replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Igal, I would start to use the debugger of the ICD2. I would want to see whether any messages are coming back from the GPS at all. I think I would simply set a break point at the location where the GPS messages have been parsed. e.g. here in the…"
May 2, 2010

DeveloperWilliam Premerlani replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"Hi Igal, 4.3 volts is fine for the GPS. Bill"
May 2, 2010
igal replied to igal's discussion Trying to setup UAV DEV BOARD and getting error when compiling.
"I have mesured 4.3V the vcc for the GPS is it OK ? In the data sheet of the GPS it is written that 4.5 - 6V is the operating voltage In a day or 2 i will connect the usart to my computer with RS232 and hope to see more info."
May 2, 2010

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.

A list of all T3 contests is here. 

 

Top Content 

1 What do you think the APM should do on fail safe

What do you think the APM should do on fail safe
2 ArduCopter 2.5 released!

ArduCopter 2.5 released!
3 Housekeeping note: Kevin Finisterre

Housekeeping note: Kevin Finisterre
4 Hexa-copter found after failed attempt of delivering cell phones to inmates of a Brazilian penitentiary

Hexa-copter found after failed attempt of delivering cell phones to inmates of a Brazilian penitentiary
5 Gauging Interest in the CNC Machine

Gauging Interest in the CNC Machine

Groups

© 2012   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service