Ugur Bozkurt
Ugur Bozkurt
  • Male
  • ankara
  • Turkey
Share Twitter
  • Blog Posts
  • Discussions (3)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Ugur Bozkurt's Friends

  • Ersin Acar

Ugur Bozkurt's Discussions

Y servo harness

Started this discussion. Last reply by Ugur Bozkurt May 24, 2009. 2 Replies

lego uav autopilot

Started this discussion. Last reply by Chris Anderson May 21, 2009. 1 Reply

 

Welcome, UgurBozkurt!

Latest Activity

Profile Icon
Ugur Bozkurt replied to Ugur Bozkurt's discussion 'Y servo harness'
thanks Chris! it will be very helpful.
May 24, 2009
Profile Icon
Chris Anderson replied to Ugur Bozkurt's discussion 'Y servo harness'
No buffer is required with a Y harness--just soldering together two servo cables is fine.
May 24, 2009
Profile Icon

Y servo harness

hi everyone!is there anyone who knows about Y harness. i have one output from co pilot computer for ailerons and i need to use this output for two servos. Y harness does this job pretty good. But i dont have it. can i use two servo extension cable by joining them in parallel like Y harness or is there any buffer circuit used in Y harness separation node. I think it causes current draw. is it problem for servos.See More
Discussion posted by Ugur Bozkurt May 23, 2009
Profile Icon
Chris Anderson replied to Ugur Bozkurt's discussion 'lego uav autopilot'
??? Mindstorms is I2C. FMA sensor is analog.
May 21, 2009
Profile Icon

lego uav autopilot

helloi have a project about lego UAV with FMA co pilot. dramatically co pilot computer burst. but elevon servo output works fine. So I will get a new fma co pilot. And I am wondering if i can use the old co pilot computer as a MUX switching between Mindstorm and Tx for controlling the rudder.if possible, i will need to connect Mindstorm instead of co pilot sensor that input has 4 pins.Thaks in AdvanceSee More
Discussion posted by Ugur Bozkurt May 21, 2009
Profile Icon
dincer hepguler left a comment for Ugur Bozkurt
UgB, ben stabilizasyon için Fma co pilot kullanmıyorum... aslında benzer bir thermophile sensorum var (Art-Tech Co Pilot) kendi sistemimde Wii Nunchuck tan elde edilmiş bir accelerometre kullanıyorum. mukemmel çalışıyor. sensor…
May 2, 2009
Profile Icon
Chris Anderson replied to Ugur Bozkurt's discussion 'fma co pilot sensor'
We've worked on two Mindstorms-based autopilots. One with the FMA Co-Pilot where these is NO connection between the Co-Pilot and Mindstorms. They are separate systems. The other, which uses Lego gyros and acceleromters, has no FMA Co-Pilot at…
Apr 30, 2009
Profile Icon
Chris Anderson replied to Ugur Bozkurt's discussion 'fma co pilot sensor'
You put the batter straight into the Co-Pilot without going through an ESC??? That would kill it for sure.
Apr 30, 2009
Profile Icon
Ugur Bozkurt left a comment for Chris Anderson
hi, do you have any idea about co pilot sensor calibration. we need to measure the output from sensors via ossilloscope. i am using fma co pilot (cpd4 ) , lipo battery, sub micro servos, dx6i radio controller. i also need to figure out how to set up…
Apr 28, 2009
Profile Icon
Ugur Bozkurt left a comment for dincer hepguler
merhaba, uav ile ilgili bir tez hazirliyorum. fakat sensor kalibrasyonu icin osiloskopta bazi olcumler yapmamiz gerekiyor. co pilot sensorunun ne kadar dondugune bagli olarak bir cikis gozlemlememiz gerekiyor. servonun nasil tepki verdigi…
Apr 28, 2009

Comment Wall (1 comment)

At 3:53am on May 2, 2009, dincer hepgulerdincer hepguler said…
UgB,
ben stabilizasyon için Fma co pilot kullanmıyorum... aslında benzer bir thermophile sensorum var (Art-Tech Co Pilot) kendi sistemimde Wii Nunchuck tan elde edilmiş bir accelerometre kullanıyorum. mukemmel çalışıyor. sensor kalibrasyonu için hiç osiloskop kullanmadım, bu sensorler sistem uzerinde ucagı degişik eksenlerde egerek kalibre edilir, bu konuda yardım edemeyecegim .. uzgunum... başarılar...

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

© 2012   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service