"wow really useful application"
viky's Discussions
How the Frequency of RC Transmitter can be changed
Started this discussion. Last reply by Riccardo Kuebler Jun 16, 2010. 2 Replies 0 Likes
A nose dive problem in self made balsa pusher configuration model.
Started this discussion. Last reply by TestPilot Jul 11, 2010. 14 Replies 0 Likes
How to replace two way switch by a 3 way switch in Futaba Transmitter
Started this discussion. Last reply by viky Jan 21, 2010. 2 Replies 0 Likes
viky's Page
Latest Activity
viky commented on Eraser's blog post A little Success with Arduino Ethernet , Vapix 3 and PTZ camera for Telemaster"Eraser, what motors are used in it for pan/tilt function, are they servo motors or stepper . Usually dome camera's have stepper which will increase the complexity of interface with arduino . It will be better if it has servo motor drive.
"
viky commented on Riccardo Kuebler's blog post How to read PPM stream and PWM pulses on sound card oscilloscope"wow ! great software, its working well....and good tool at ur desktop itself."
viky commented on Melih Karakelle's blog post Serving the Electronics"Open FARC is interesting one."
viky commented on Paul Mather's blog post First person flight through Google Earth HK - GCS Update"Its better to try this all with wireless link instead of connecting directly FTDI to AP. That may work."
viky commented on Adam Barrow's blog post UDB Waypoint editor"Its alright billu bhaiya, we will wait till it works.Thanks to you and adam , apart from ur busy schedules you r doing a lot for community. Its quite useful tool, so it tempted me to try it at the earliest."
viky commented on Adam Barrow's blog post UDB Waypoint editor"Its not working still, i tried in chrome and explorer.No map displayed"
viky commented on Patrick Mccabe's blog post My New AGV"great patrick , u r doing great job, carry on ."
Riccardo Kuebler replied to viky's discussion How the Frequency of RC Transmitter can be changed"Viky,
if you want to stay with PCM rx you can use all Futaba PCM rx. PCM is proprietary, so no interchangeable. Otherwise you can use other brand rx in PPM mode. I used Futaba PPM rx too with Graupner TX.
About crystals you can use all the…"
Morli replied to viky's discussion How the Frequency of RC Transmitter can be changed"it may not. For the price of new Rx and crystal , you might be better off with one of Assan 2.4 or Corona hack module from HK"
viky posted a discussionHow the Frequency of RC Transmitter can be changed
Dear all, I was using a 40 MHz T6EXP Futaba transmitter in PCM mode with the PCM Receiver of same frequency R13P 6 channel Futaba Receiver with 40 Mhz crystal. Just few days back i lost my receiver , and could not find the same available with 40 Mhz crystal. I have a doubt can i have a different receiver with apair of crystal. And Will the transmitter work with different crystal or it is designed to work only on 40 MHz. PLease Help regarding this.With RegardsVikramSee More
hawk replied to viky's discussion A nose dive problem in self made balsa pusher configuration model."Yes viky,
I know you are very concentrate ur Design.good luck with your job.I use Aeropack and AeroSim software using MathLab .u can downlaod free.
thanks"
viky replied to viky's discussion A nose dive problem in self made balsa pusher configuration model."Oh thanks hawk , it was very old problem we were facing and we were able to resolve it by advise of few experts like you had given. And you r right hawk we had concentrated on thrust line. to confirm our exact thrust line setting , We hang the plane…"
hawk replied to viky's discussion A nose dive problem in self made balsa pusher configuration model."Hi viky's,
good experience! I thinks you should check the thrust line location .You need to change the thrust line position near the wing chord line with zero angle.
thanks"
hawk replied to viky's discussion A nose dive problem in self made balsa pusher configuration model."Hi,
you should check thrust line to be zero angle and to put nearly wind chord.
How it?"
viky commented on Patrick Mccabe's blog post AGV update"You may use rf link to give commands to ur robot instead of pressing switch on robot itself . Can do it by wireless, will be much better isn't it."
Profile Information
- Tell us a bit about your UAV interest
- Love gliders
- Hometown:
- CHD
Viky's Blog
How to change labview GCS Baudrate to 19200...
Posted on August 28, 2009 at 6:15am 11 Comments 0 Likes
Hi all, i had to make little changes in program to get the data at 19200 baud rate...... so its all woking with wireless telemetry.. But the only problem is groundstation... how to change baud rate of ground station. Since its in labview so facing problem of changing its baud rate i have its source code also but cant get how to change.. ..or is there any software emulator to get data on 19200 and reproduce on other serial port at 57600 for GCS.. Suggestions please ..
Done a air test today
Posted on August 13, 2009 at 4:18am 11 Comments 0 Likes
Today i have done a ground test and it shown good results on ground navigation test it sensed the location i changed code little bit for navigation so that it shows the waypoint achieved with the buzzer beep. And it was succesfuly alarmed me the waypoint captured . The next step i did i load 2.0 version and i have fma xy sensor, and no telemetry so used buzzer for ground test navigation. Well i put the original code of jordi of 2.0 ver and i just did the settings as prescribed in 2.0 user… Continue
Changed the 2.1 for 2.0 hardware features.....
Posted on August 3, 2009 at 9:04pm 0 Comments 0 Likes
Hi all, i m ready for the ground test.Before starting i would like to clarify few things here..
I dont have Z sensor and air speed sensors soofcourse no throttle control then also... I was ok with version 2.0 but since i would like to add the config utility feature without increasing any hardware. So i made few changes in 2.1 version so that it can work successfuly with 2.0's hardware(only XY sensor).
I have made these changes please confirm is it right and please tell me if any… Continue
I dont have Z sensor and air speed sensors soofcourse no throttle control then also... I was ok with version 2.0 but since i would like to add the config utility feature without increasing any hardware. So i made few changes in 2.1 version so that it can work successfuly with 2.0's hardware(only XY sensor).
I have made these changes please confirm is it right and please tell me if any… Continue
Comment Wall (20 comments)
- At 12:11am on July 29, 2009,
Raghav Jain said… - hi,
good to find people interested in uavs in India.
what else are your interest.
- At 5:47am on August 1, 2009, Raghav Jain said…
- oh! that sounds great what else do you know about uavs, i am very new to it and i am trying t learn the electronics involved in it.
- At 10:53pm on August 4, 2009, Raghav Jain said…
- hi, u said you have designed your own uav is that correct.
i can see its picture
- At 11:48pm on August 4, 2009, Raghav Jain said…
- oh thats great , but where r u doing all this stuff
- At 12:18am on August 5, 2009, Raghav Jain said…
- which city
- At 12:18am on August 5, 2009, Raghav Jain said…
- r u on skype
- At 12:40am on August 5, 2009, Raghav Jain said…
- no dude thats not mine and thats not a UAV its an ncc aircraft
- At 1:27am on August 5, 2009, Raghav Jain said…
- no i dont have one, but i do have rc model which i fly on weekends , i am very new to uav
- At 1:27am on August 5, 2009, Raghav Jain said…
- 10months or so
- At 12:03am on August 7, 2009,
Rana said… - Yeah, m also working on uav. I have x-bees and also using in ardu 2.
I am also working on UAVP & UAVX. Have sucessfully built & flight tested UAVP based on PIC18F2520 / 2620.
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The third round was a reliablilty/aerial photography round for both planes and copters, which is now closed. Stay tuned for the next round, beginning soon.A list of all T3 contests is here.
Top Content
Groups
-
DIYDrones - CNC Project
61 members
-
Moderators
57 members
-
ArduPilot (legacy) User …
95 members
-
ArduCopter Evolution Team
108 members
-
ArduCopter User Group
617 members
© 2012 Created by Chris Anderson.
