Gender
Male
About
Location
derby
About Me:
well into rc
Please tell us a bit about your UAV interest
just getting into it trying to get my new stuff working
Hometown:
derby
Activity Feed
"Hi I us the gimble channel and rc 7 to make my landing gear go up and down
Stuart"
Stuart"
"Hi would the software fix make the hardware fix unnecessary?
Stuart"
Stuart"
"hi
do you mean put a 1k resistor across + and - where escs plug in or where camera gimble plugs in /aux out ?
cheers stuart"
do you mean put a 1k resistor across + and - where escs plug in or where camera gimble plugs in /aux out ?
cheers stuart"
"Hi
Plugged mine in in the house about 20 deg went outside armed and flew then after a few mins would not hold position as it was 0degs
started to slop off so I think gyros or accelerometers didn't like temp change
Reconnected power outside and flew…"
Plugged mine in in the house about 20 deg went outside armed and flew then after a few mins would not hold position as it was 0degs
started to slop off so I think gyros or accelerometers didn't like temp change
Reconnected power outside and flew…"
"I have a mini apm 250quad v3.2.1 throttle max is there but on my pixhawk v3.3.2 no throttle max on my quad or hex but both fly fine have you calibrated your escs just a thought
Stuart"
Stuart"
"Hi
I us a Ublox NEO-M8N as my main gps which gets 15 sats in my living room and a second 3dr gps which is still thinking about getting a lock in the house with gps auto switch on it never actually switches gps but 3dr one is there should the m8one…"
I us a Ublox NEO-M8N as my main gps which gets 15 sats in my living room and a second 3dr gps which is still thinking about getting a lock in the house with gps auto switch on it never actually switches gps but 3dr one is there should the m8one…"
"Hi did you manage to look at my log
Stu"
Stu"
"Hi I used to have two 3dr gps but it kept jumping say a couple of meters so I fitted a m8n which gets between 16 and 18 sats so there is no jump as the 3dr only gets 11 at most but should the m8n fail it hopefully will switch to the 3dr one and at…"
"hi please find attached log
many thanks stuart2015-11-08 13-28-41.bin"
many thanks stuart2015-11-08 13-28-41.bin"
"Thanks I thought it might be on limits of the motor and props don't really want to go any more power or I'd loose flight time
Stuart"
Stuart"
"My setup
17x5.5inch props
390kv motors
30amp Simonk afro esc
10000mah 4s
Pixhawk 2.4.6
Flys for half an hr20151108_183445.jpg"
17x5.5inch props
390kv motors
30amp Simonk afro esc
10000mah 4s
Pixhawk 2.4.6
Flys for half an hr20151108_183445.jpg"
"vibration levels abit high but there was a 23mph gust winds
vibration within normal levels on not so windy days
stu"
vibration within normal levels on not so windy days
stu"
"hi please find attached log
many thanks stuart2015-11-08 13-28-14.tlog"
many thanks stuart2015-11-08 13-28-14.tlog"
"Will do but hopefully tomoz as is 11.10at night here lol so if it's not raining I'll try tomorrow cheers stuart"
"Oh sorry no I only covered with cling film over the top to stop wind blowing in directly it was no where near air tight or all around
I still got height reading on mission planer
Cheers stuart"
I still got height reading on mission planer
Cheers stuart"
"Hi yes there is dense foam over the barometer in the pixhawk case
Stuart"
Stuart"
